Steam and hot water pipeline units are parts of pipeline constructed for joining separate parts of it with or without changing of direction or flow passage (rejection, junction, tee-joint, pipe plug, fluid cap)
Omental compensators are an assembly units that ensure compensation of linear thermal expansion of pipelines.
Assembly units for metal riggers are details and assembly units (stand, collar, handrail, flooring, farm, rigging screw and plunger pin) that bear the burden from equipment and repair workers for safety purposes.
Vessels, tanks and containers of the kind made of ferrous materials for all substances (except compressed and liquefied gas) with 300 l capacity, without mechanical and heat engineering equipment are stationary vessels designed for gaseous, liquid and solid substances.
Vessels of 1-4 groups that operate under pressure of 30,0 МPа and its compounds are hermetically sealed vessels that are designed for conducting chemical, thermal and other technological procedures and for stocking and transportation of gaseous, liquid and other substances.
Containers, vessels for solid substances are stationary vessels designed for stocking solid substances.
Boxes and other reservoirs from ferrous materials for all substances (except compressed and liquefied gas)with 50 L capacity or more are stationary reservoirs for stocking vapor, liquid and other substances.
Fastenings for heating areas of steam and waterheating boilers are parts welded to external surface of boiler unit (pipe, collector, blow case) and isolation fastening, bearing-harness system and pipe spacing designed for additional function.
Air-heating cubes, recuperative air heaters (tubular) for steam boilers with 420 tons steam power capacity per hour are devices designed for warmth transferring from furnace gases to air trough tube walls which ends are welded into holes of tube plates.
Metrical and membranaceous subassemblies are assembly units of pipelines designed for discharge measurements of the environment.
Boiler heating tubular surface elements with cells are boiler assembly units designed for getting steam and hot water with pressure above atmospheric absolute and used outside the unit itself.
Steam and hot water pipelines are facilities made of tubes, parts, fittings fayed with each other and designed for steam and hot water transportation.
Feed-water economizer units are one single device heated by end products of fuel combustion and designed for heating or partial evaporation of water that comes into steam boiler.
Superheater is a device designed for increasing steam temperature above saturation point than pressure in the boiler.
Spray desuperheaters are devices designed for steam parameters regulation by supplying condensate.
Heating surface cells are boiler assembly units designed for pipe junctures and changing flow direction.
Condensators are devices for steam cooling and transferring it into liquid state.
Tubular air heater sections are devices designed for warmth transferring from furnace gases to air through tube walls with ends welded into cavities of tube plates.
Tube bundle assemblies to superheat controls is a unit of surface steam cooler that consists of tube plates with U-shape coil pipes for steam temperature regulation.
Gas flue baskets, lens compensators, chimney valves are assembly units that ensure transportation, direction alteration, coalescence or separation, broadening or narrowing of air or gas stream.
Support and hanger details for gas and air pipes and pipelines are parts welded to external surface and designed for exercising some function of bearing-harness system, isolation fastening and gas flue, air flue and pipeline spacing.
Metalware made of ferrous materials are supports, columns, farms, platforms, falsework.
Oil-gas burner is a device that transfers fuel (gas, fuel oil), air needed for its combustion to boiler furnace for stable firing.
Atomizer burner is a device for supply and spraying of liquid fuel that comes in the boiler furnance.
Disk type adjusting valves of boiler feed water D50, D65, D100, D225, D250 is a device for water control at changing pressures and conditions at different technological procedures of power stations and boiler rooms.
Adjusting valves of lever type heating water D500, D600, D700, D1000 is a device for pressure support in heat distribution network at changing pressures and conditions.
Adjusting assemblies of disk type injection and blowing D50 is a device for water control changing pressures and conditions at different technological procedures of power stations and boiler rooms.
Elastic pin coupling is a device designed for smooth torque transmission.
Segments of underbandage insulation for rotors of turbogenerators are used for insulation of head parts of rotor windingfrom bandage rings.
Evenly regulated oil immersed arc-extincted reactor with the adjustable clearance of magnet line (RZDPOM) at short-circuits to the earth in networks having insulated neutral.